Wood Wedding Arches

Wood Wedding Arches – My fiancé and I really wanted a large wooden arch for our fall wedding – but when we looked around for prices, we knew we wouldn’t spend $200 or more to have one we could make ourselves. We spent $70 at Home Depot and this turned out great! Can’t wait to have it there at the altar for our big day 😉 And knowing WE made it together will make it even more special! I mean he did a lot of work and all I did was take notes and ask questions and I probably frustrated him more than I helped BUT we did it together 😉

Start laying out your wood so you get a good idea of ​​what you’re going to do.

Wood Wedding Arches

Using a straightedge, draw a line from the end of the board to the other side of the board at the 10 1/2″ mark (as shown below).

Stunning Wedding Arches & Altar Ideas For An Outdoor Ceremony

*When you draw your corner lines for the top section, make sure you draw the opposite corners so that the ends are visible. You don’t want to end up with corners that both go the same way – you want them to face each other. And remember to always check your lines before cutting 😉 As the saying goes, measure twice, cut once

Next, place the vertical pieces on top of the horizontal piece, align it with the 20″ line we traced at the beginning of this activity, and set it up.

(Be sure to place them within the 20″ line so that the space between the corner and the vertical piece is 4″).

Screw them in place, being careful not to over tighten the screws – you don’t want the sharp ends coming out the other end.

All Things Cedar Pagoda 94

*Here are some tips to make sure you don’t run into other screws. . . if you worked the last one in the corners, do it in a North, South, East, West pattern. Or vice versa if you scratched the first ones in N, S, E, W pattern 😉

As we installed our shelves and as fast as we went, the front of the gazebo will not show any screw heads. I like that – I wanted my building to be rustic, but I didn’t want to see a bunch of shiny idiots everywhere. (My husband is very smart).

Using the remaining 8-foot 2″ x 6″ board, cut in half for the lower arbor pieces.

Mark the center of the wooden feet so you know where to insert them into the smaller pieces.

Wedding Arch Rental In Mesa, Az

Tape the bottom pieces to the bottom of the vertical planks. (This works best if you insert screws into the base

You put them in a standing shelf). Make sure you screw the screws all the way in so that your base stays firmly in place.

This will require you to cut 4 angled pieces (2 per side) from a 10 foot 2″ x 4″ board.

Then, using a miter saw, cut a 45-degree angle on each end of the flat side of the wood.

Amazon.com: Wood Wedding Arch Triangle Arch Natural Wood Backdrop Stand Wooden Arch Decor Rustic Wedding Arch Decorations For Garden Wedding Parties, 120x150x30cm

Now screw the toenail into the bottom pieces to make it nice and secure. If you don’t know how to do it, this video explains it quickly and easily (shout out to my love for doing this for me!).

If you don’t want these bits here, you can skip them altogether. But personally I like the way they look up there and I think they’ll be perfect if I wrap some fabric and greenery around the top of the area.

For these pieces, use a 2″ x 4″ board and cut two 28″ long pieces.

Cut them at a 45 degree angle as shown below. On the other side of the board, cut the corner in the opposite direction.

The Most Unique Handcrafted Wedding Arch

Then measure 17 1/2″ down from the bottom of the horizontal piece to the top and mark on your vertical board.

This piece of bracket mounts with a vertical piece but pushed up between the two top pieces of the arbor.

Toenail board in it (so no screw heads visible from the back). Add the screw to the horizontal board (again, make sure it comes from the back so no screw heads are visible).

We used this Minwax Espresso Stain – we let it sit for about 3-4 minutes before wiping it off. We were working in temperatures over 100 degrees and without any humidity, so I wanted to make sure it wouldn’t be there for long. (Be sure to follow the directions on the can.) Great! To make our arch we took three pieces of 2 x 4 x 12 ft pieces of compressed wood and one piece of 2 x 4 x 8 ft. We found 12 foot pieces cut to 7 feet at the hardware store so we were left with 3 x 7 foot pieces and 3 x 5 foot pieces. We also grabbed some wood screws that were 2 1/2 inches long.

Brown Wood Diy Round Wedding Arch Backdrop Stand

We start with our 3.7ft pieces and we are roughing in the shape of the arch. On the piece above the arch we measured in 1ft from each side. We set up the piece that goes vertically outside the 1ft line. Next we took our wood screw and added two screws diagonally from each other to attach the vertical piece to the horizontal piece. Repeat on the other side. Yes, it’s included!

Next, we’ll take one of our 5 ft pieces and figure out how we want our support pieces to fit. So we decided we need a 26 inch piece and we need to cut a piece of wood at a 45 degree angle to one side. The easiest way to cut at a 45 degree angle is to use a miter box! It’s a plastic box with slots in 90 degree and 45 degree angles, so it makes viewing the angle easy! Now that we have another 45 degree cut, we want to make another one that goes in the opposite direction and we want the length to be 26 inches tip-to-tip. So we need to do this a total of 6 times, which means you get 2 from each 5-foot piece of wood. To make things go faster we ended up using a miter box to draw our 45 degree angle and a circular saw to cut it, but if you don’t have a circular saw you can use a miter box and a handsaw (it just might take longer) . Okay, you have 6.26 inch bracket pieces, we’ll go back to our bow and flip it over so the back is facing up. In one of the corners we added the extra 8 foot piece of wood as in the sky and then aligned the support piece with the vertical piece and placed it on top of the top piece. We added two screws on top of the crosspiece, easy, but to attach it to the side you have to come from the side. To make this easier we have pre-drilled a small hole for our screw in the corner, this will make adding the screw in the corner easier.

Repeat on the other side and now we have a well supported arch. So our next step is to cut our 8ft 2×4 in half to make it 4ft long. This goes under our raised pieces to make the floor supports and brushes. We marked the center point on our piece 4ft, so two feet so we know where our piece should sit. This is how we will use the remaining four 26 inch corner pieces. Using a square to make sure the angle is exactly 90 degrees, add your 45 degree corner piece until it lays flat against the bottom piece and side piece. We then used the same hole pattern we used above so we could get the screw in at an angle. We attached the angled pieces with two screws in the lower part and two in the side of the building. We repeated this to the back of the arch. Go ahead and repeat the entire process on the other side of the arch. In the end you have a strong bow. If you are concerned about wind, you can dig holes or add sandbags and logs through the lower legs.

Our last step is to decorate our bow! You can do this any way you like, but we decided to use a staple gun to staple long pieces of white fabric to the top and flow to the front. This is the fabric left over from the panels I made for my loft bedroom (or yours

Diy Wood Wedding Arbor — The Sorry Girls

Rustic wedding arches, etsy wedding arches, wood arches for wedding, round wedding arches, wedding arches, diy wedding arches ideas, decorative wood arches, balloon arches for wedding, wedding arches diy, wedding arches with flowers, wood arches, wedding arches for sale

Related For Wood Wedding Arches

Masquerade Masks Centerpieces

Masquerade Masks Centerpieces – A stunning blend of shimmering

White And Turquoise Wedding

White And Turquoise Wedding – We use cookies to

Poll How Many Dpos When You Got Bfp

Poll How Many Dpos When You Got Bfp After

October Wedding Decorations

October Wedding Decorations – Kaka, or autumn, is a